Abstract: Robots have begun to transition from assembly lines, where they are physically separated from humans, to human-populated environments and human-enhancing applications, where interaction with people is inevitable. With this shift, research in human-robot interaction (HRI) has grown to allow robots to work with and around humans on complex tasks, augment and enhance people, and provide the best support to them. In this talk, I will provide an overview of the work performed in the HIRO Group and our efforts toward intuitive, human-centered technologies for the next generation of robot workers, assistants, and collaborators. More specifically, I will present our research on: a) robots that are safe to people, b) robots that are capable of operating in complex environments, and c) robots that are good teammates. In all, this research will enable capabilities that were not previously possible, and will impact work domains such as manufacturing, construction, logistics, the home, and health care.
Bio: Alessandro Roncone is Assistant Professor in the Computer Science Department at University of Colorado Boulder. He received his B.Sc. summa cum laude in Biomedical Engineering in 2008, and his M.Sc. summa cum laude in NeuroEngineering in 2011 from the University of Genoa, Italy. In 2015 he completed his Ph.D. in Robotics, Cognition and Interaction Technologies from the Italian Institute of Technology [IIT], working on the iCub humanoid in the Robotics, Brain and Cognitive Sciences department and the iCub Facility. From 2015 to 2018, he was Postdoctoral Associate at the Social Robotics Lab in Yale University, performing research in Human-Robot Collaboration for advanced manufacturing. He joined as faculty at CU Boulder in August 2018, where he is director of the Human Interaction and Robotics Group (HIRO, https://hiro-group.ronc.one/ ) and co-director of the Interdisciplinary Research Theme in Engineering Education Research and AI-augmented Learning (EER-AIL IRT, https://www.colorado.edu/irt/engineering-education-ai/ ).
Abstract: The target of human flight in space is missions beyond low earth orbit and the Lunar Gateway for deep space exploration and Missions to Mars. Several conditions, such as the effect of weightlessness and radiations on the human body, behavioral health decrements, and communication latency have to be considered. Telemedicine and telerobotic applications, robot-assisted surgery with some hints on experimental surgical procedures carried out in previous missions, have to be considered as well. The need for greater crew autonomy in dealing with health issues is related to the increasing severity of medical and surgical interventions that could occur in these missions, and the presence of a highly trained surgeon on board would be recommended. A surgical robot could be a valuable aid but only insofar as it is provided with multiple functions, including the capability to perform certain procedures autonomously. Providing a multi-functional surgical robot is the new frontier. Research in this field shall be paving the way for the development of new structured plans for human health in space, as well as providing new suggestions for clinical applications on Earth.
Bio: Dr. Desire Pantalone MD is a general surgeon with a particular interest in trauma surgery and emergency surgery. She is a staff surgeon in the Unit of Emergency Surgery and part of the Trauma Team of the University Hospital Careggi in Florence. She is also a specialist in General Surgery and Vascular Surgery. She previously was a Research Associate at the University of Chicago (IL) (Prof M. Michelassi) for Oncological Surgery and for Liver Transplantation and Hepatobiliary Surgery (Dr. J Emond). She is also an instructor for the Advanced Trauma Operative Management (American College of Surgeons Committee for Trauma) and a Fellow of the American College of Surgeons. She is also a Core Board member responsible for “Studies on traumatic events and surgery” in the ESA-Topical Team on “Tissue Healing in Space: Techniques for promoting and monitoring tissue repair and regeneration” for Life Science Activities.
Student 1: Maia Stiber “Supporting Effective HRI via Flexible Robot Error Management Using Natural Human Responses”
Abstract: Unexpected robot errors during human-robot interaction are inescapable; they can occur during any task and do not necessarily fit human expectations of possible errors. When left unmanaged, robot errors’ impact on an interaction harms task performance and user trust, resulting in user unwillingness to work with a robot. Prior error management techniques often do not possess the versatility to appropriately address robot errors across tasks and error types as they frequently use task or error specific information for robust management. In this presentation, I describe my work on exploring techniques for creating flexible error management through leveraging natural human responses (social signals) to robot errors as input for error detection and classification across tasks, scenarios, and error types in physical human-robot interaction. I present an error detection method that uses facial reactions for real-time detection and temporal localization of robot error during HRI, a flexible error-aware framework using traditional and social signal inputs that allow for improved error detection, and an exploration on the effects of robot error severity on natural human responses. I will end my talk by discussing how my current and future work further investigates the use of social signals in the context of HRI for flexible error detection and classification.
Bio: Maia Stiber is a Ph.D. candidate in the Department of Computer Science, co-advised by Dr. Chien-Ming Huang and Dr. Russell Taylor. Her work focuses on leveraging natural human responses to robot errors in an effort to develop flexible error management techniques in support of effective human-robot interaction.
Student 2: Akwasi Akwaboah “Neuromorphic Cognition and Neural Interfaces”
Abstract: I present research at the Ralph Etienne-Cummings-led Computational Sensor-Motor Systems Lab, Johns Hopkins University on two fronts – (1) Neuromorphic Cognition (NC) focused on the emulation neural physiology at algorithmic and hardware levels, and (2) Neural Interfaces with emphasis on electronics for neural MicroElectrode Array (MEA) characterization. The motivation for the NC front is as follows. The human brain expends a mere 20 watts in learning and inference, exponentially lower than state-of-the-art large language models (GPT-3 and LaMDA). There is the need to innovate sustainable AI hardware as the 3.4x compute doubling per month has drastically outpaced Moore’s law, i.e., a 2-year transistor doubling. Efforts here are geared towards realizing biologically plausible learning rules such as the Hebb’s rule-based Spike-Timing-Dependent Plasticity (STDP) algorithmically and in correspondingly low-power mixed analog-digital VLSI implements. On the same front of achieving a parsimonious artificial intelligence, we are investigating the outcomes of using our models of the primate visual attention to selectively sparsify computation in deep neural networks. At the NI front, we are developing an open-source multichannel potentiostat with parallel data acquisition capability. This work holds implications for rapid characterization and monitoring of neural MEAs often adopted in neural rehabilitation and in neuroscientific experiments. A standard characterization technique is the Electrochemical Impedance (EI) Spectrometry. However, the increasing channel counts in state-of-the-art MEAs (100x and 1000x) imposes the curse of prolonged acquisition time needed for high spectral resolution. Thus, a truly parallel EI spectrometer made available to the scientific community will ameliorate prolonged research time and cost.
Bio: Akwasi Akwaboah joined the Computational Sensory-Motor Systems (CSMS) Lab in Fall 2020 and is working towards his PhD. He received the MSE in Electrical Engineering from the Johns Hopkins University, Baltimore, MD in Summer 2022 en route the PhD. He received the B.Sc. Degree in Biomedical Engineering (First Class Honors) from the Kwame Nkrumah University of Science and Technology, Ghana in 2017. He also received the M.S. degree in Electronics Engineering from Norfolk State University, Norfolk, VA, USA in 2020. His master’s thesis there focused on the formulation of a heuristically optimized computational model of a stem cell-derived cardiomyocyte with implications in cardiac safety pharmacology. He subsequently worked at Dr. James Weiland’s BioElectronic Vision Lab at the University of Michigan, Ann Arbor, MI, USA in 2020; where he collaborated on research in retinal prostheses, calcium imaging and neural electrode characterization. His current interests include the following: neuromorphic circuits and systems, bio-inspired algorithms, computational biology, and neural interfaces. On the lighter side, Akwasi loves to cook and listen to classical and Afrobeats music. He lives by Marie Curie’s quote – “Nothing in life is to be feared, it is only to be understood …”
Panel Speaker 1: Erin Sutton, PhD
Guidance and Control Engineer at the JHU Applied Physics Laboratory
Ph.D. Mechanical Engineering 2017, M.S. Mechanical Engineering 2016
Erin Sutton is a mechanical engineer at Johns Hopkins Applied Physics Laboratory. She received a BS in mechanical engineering from the University of Dayton and an MS and a PhD in mechanical engineering from Johns Hopkins University. She spent a year at the Naval Air Systems Command designing flight simulators before joining APL in 2019. Her primary research interest is in enhancing existing guidance and control systems with autonomy, and her recent projects range from hypersonic missile defense to civil space exploration.
Panel Speaker 2: Star Kim, PhD
Job title and affiliation: Management Consultant at McKinsey & Company
Ph.D. Mechanical Engineering 2021
Star is an Associate at a global business management consulting firm, McKinsey & Company. At JHU, she worked on personalizing cardiac surgery by creating patient specific vascular conduits at Dr. Axel Krieger’s IMERSE lab. She made a virtual reality software for doctors to design and evaluate conduits for each patient. Her team filed a patent and founded a startup together, which received funding from the State of Maryland. Before joining JHU, she was at the University of Maryland, College Park and the U.S. Food and Drug Administration. There, she developed and tested patient specific medical devices and systems such as virtual reality mental therapy and orthopedic surgical cutting guides.
Panel Speaker 3: Nicole Ortega, MSE
Senior Robotics and Controls Engineer at Johnson and Johnson, Robotics and Digital Solutions
JHU MSE Robotics 2018, JHU BS in Biomedical Engineering 2016
At Johnson and Johnson Nicole works on the Robotis and Controls team to improve the accuracy of their laparoscopic surgery platform. Before joining J&J, Nicole worked as a contractor for NASA supporting Gateway and at Think Surgical supporting their next generation knee arthroplasty robot.
Panel Speaker 4: Ryan Keating, MSE
Software Engineer at Nuro
BS Mechanical Engineering 2013, MSE Robotics 2014
Bio: After finishing my degrees at JHU, I spent two and a half years working at Carnegie Robotics, where I was primarily involved in the development of a land-mine sweeping robot and an inertial navigation system. Following a brief stint working at SRI International to prototype a sandwich-making robot system (yes, really), I have been working on the perception team at Nuro for the past four and a half years. I’ve had the opportunity to work on various parts of the perception stack over that time period, but my largest contributions have been to our backup autonomy system, our object tracking system, and the evaluation framework we use to validate changes to the perception system.
All LCSR members, their families, and significant others are invited to the:
Ugly (or normal) Sweater Bash
Friday, December 9th
You can help by contributing your favorite holiday dish (regional specialties strongly encouraged!) to this pot-luck get together (you don’t have to bring anything to participate). Main dishes will be provided, as will plates, napkins, utensils, etc. Click here to sign up
There will a gingerbread decorating contest and prizes for best/ugliest sweater!